Hyundai Tucson: DCT (Dual Clutch Transmission) System (SBW)
Troubleshooting
Specifications
Clutch Actuator
Gear Actuator
Inhibitor Switch
- Type: Combination of output signals from 4 terminals
- Specifications
Input speed sensor
Tightening Torques
Lubricants
Special Service Tools
Tool (Number and Name)/ Illustration/ Use
Engine
support fixture
(Beam)
09200-3N000/ 
/ Removal and
installation of the
transmission.
Use this beam (SSTNo. : 09200- 3N000) with the supporter (SST No. : 09200- 2S200).
Permit operating with 09200-38001.
09200-2S200
Engine
support fixture
(Supporter)/ 
/ Removal and
installation of the
transaxle.with the
beam (SST No. :
09200-
38001/3N000).
09200-L1200
Engine
support fixture
(Front)/ 
/ Removal and
installation of the
transaxle.
09200-4X000
Engine
support fixture
(Adapter)/ 
/ Removal and
installation of the
transaxle.
Use this beam (SST No. : 09200- 3N000)
09473-D3500
Oil seal
installer/ 
/ Used for installing
driven gear oil seal
Used with the
handle (09231-
H 1 1 0 0 ) 4WD
09453-3L240
Oil seal
installer/ 
/ Used for installing
differential oil seal
Used with the
handle (09231-
H 1 1 0 0 )
Handle
09231-H1100/ 
/ Used for installing
differential oil
sealUsed with the
installer (09453-
3L240)
0943 0-2C110
Position
sensor neutral
fixed jig/ 
/ Used to align the
neutral position
when installing the
position sensor.
Dual clutch
remover
09430-C1180/ 
/ Used for removing
dual clutch
assembly
Dual clutch
Installer
09430-2A240/ 
/ Used for installing
dual clutch
assembly
Clutch
actuator
adjuster
0K430-Q5300/ 
/ Used for adjusting
clutch actuator
Clutch
actuator
remover &
installer
0K430-Q5100/ 
/ Removal and
installation of the
clutch actuator
assembly.
- DCT (Dual Clutch Transmission) System (SBW)- Removal
- DCT (Dual Clutch Transmission) System (SBW)- Installation
- DCT (Dual Clutch Transmission) System (SBW)- Inspection
- Clutch Actuator & TCM- Assembly Replacement
- Transmission Control Module (TCM) Inspection Procedure
- Clutch actuator assembly - Components
- Gear actuator assembly
- Gear actuator assembly- Installation
- Input shaft speed sensor
- Input shaft speed sensor- Removal
- Input shaft speed sensor- Installation
- Clutch fork and clutch bearing
READ NEXT:
DCT (Dual Clutch Transmission) System (SBW)- Removal
Components
DCT (Dual Clutch Transmission) assembly
DCT support bracket
Roll rod support bracket
Removal
Turn ignition switch OFF and disconnect the negative (-) battery cable.
Remove the air cleaner assembly and air duct.
DCT (Dual Clutch Transmission) System (SBW)- Installation
Installation
To install, reverse the removal procedure.
WARNING
Matters that require attention when installing the dual clutch
transmission (DCT) to engine
l)Check the pilot bearing (B) and external damper (A) 011 the side of engine for
DCT (Dual Clutch Transmission) System (SBW)- Inspection
Inspection
WARNING
In principle, the transmission oil is maintenance-free, and no
exchange is required.
But it must be inspected and replenished every 4 years or 40,000 miles.
Uplift the vehicle with lift.
Remove the engine room under co
SEE MORE:
Measuring the resistance of the pressure sensor- Adjustment
Adjustment
Description
The friction material inside the coupling will degrade over time. Therefore,
corresponding compensation values must be referenced
and entered after replacing the controller or the coupling.
Compensation Requirement and Pr
Pinion drive gear assembly
Fix the differential carrier assembly using the SST (09501-C9230,
0K530-P2500, 0K501-P2232).
Loosen the pinion gear lock nut using the SST (09501-C9230).
WARNING
When istalling lock nut, use a new one.
Remove the pinion dr
Information
- Home
- Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Owner's Manual
- Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Workshop Manual
