TucsonDataManu

.com

Hyundai Tucson: Exhaust Gas Temperature Sensor (EGTS)

Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Workshop Manual / Engine Control - Fuel System / Exhaust Gas Temperature Sensor (EGTS)

Description

Exhaust Gas Temperature Sensor (EGTS) is installed on Gasoline Particulate Filter (GPF) senses the temperature of exhaust gas flowing into. When pre-determined engine condition is set, ECM burns soot gathered in GPF with exhaust gas. At this time, the exhaust gas temperature is an important factor of engine condition

Exhaust Gas Temperature Sensor (EGTS) #1 GPF Type

Exhaust Gas Temperature Sensor (EGTS) #2 GPF Type

Exhaust Gas Temperature Sensor (EGTS) #2 GPF Type

Specification

Specification

Exhaust Gas Temperature Sensor (EGTS) #1, 2 GPF Type

 Type : Thermistor type

Circuit Diagram

Circuit Diagram

Exhaust Gas Temperature Sensor (EGTS) #1 GPF Type

Harness Connector

Harness Connector

Exhaust Gas Temperature Sensor (EGTS) #2 GPF Type

Exhaust Gas Temperature Sensor (EGTS) #2 GPF Type

Harness Connector

Harness Connector

Inspection

Inspection

  1. Turn ignition switch OFF.
  2. Disconnect the connector of exhaust gas temperature sensors.
  3. Measure resistance between sensor signal terminal and ground terminal.
  4. Check that the resistance is within the specification.

Specification : Refer to "Specification"

Removal

Exhaust Gas Temperature Sensor (EGTS) #1 GPF Type

  1. Turn the ignition switch OFF and disconnect the battery negative (-) terminal.
  2. Lift up the vehicle.
  3. Remove the floor under cover.
  4. Disconnect the egts connector (A).

  1. Remove the egts sensor (A).

Tightening torque : 39.2 - 49.0 Nm (4.0 - 5.0 kgfm, 28.9 - 36.1 lb ft)

Exhaust Gas Temperature Sensor (EGTS) #2 GPF Type

Exhaust Gas Temperature Sensor (EGTS) #2 GPF Type

  1. Turn the ignition switch OFF and disconnect the battery negative (-) terminal.
  2. Lift up the vehicle.
  3. Remove the floor under cover.
  4. Disconnect the egts connector (A).

  1. Remove the egts sensor (A).

Tightening torque : 39.2 - 49.0 N m (4.0 - 5.0 kgfm, 28.9 - 36.1 lb ft)

Installation

Installation

WARNING

  • Install the component to the specified torques.
  • Note that internal damage may occur when the component is dropped. In this case, use it after inspecting.
  1. Install in the reverse order of removal.

    READ NEXT:

     EGR Temperature Sensor

    Description EGR temperature sensor is used for temperature measurement and EGR bypass valve function diagnosis as well as thermal protection of EGR system. Specification Type : Thermistor type Circuit Diagram Harness Connecto

     Accelerator Position Sensor (APS)

    Description Accelerator Position Sensor (APS) is installed on the accelerator pedal module and detects the rotation angle of the accelerator pedal. The APS is one of the most important sensors in engine control system, so it consists of the tw

     Oil Temperature Sensor (OTS)

    Description It generates the oil pressure and temperature information (output voltage) to control the pump operation proportional control valve in variable oil pump system. It measures the oil pressure and temperature discharged from the oil p

    SEE MORE:

     Highway Driving Assist (HDA)

    Highway Driving Assist is designed to help detect vehicles and lanes ahead, and help maintain distance from the vehicle ahead, maintain the set speed, and help center the vehicle in the lane while driving on the highway (or motorway). Info

     Brake Booster Operating

    Components Reservoir cap Reservoir Brake booster Master cylinder Push rod Test Run the engine for one or two minutes, and then stop it. If the pedal depresses fully the first time but gradually becomes higher when depressed

    Information

    2022-2025 © - www.tucsondatamanu.com