Hyundai Tucson: LCD Display Messages for Vehicles Equipped with Smart Key
Shift to P
This message is displayed if you try to turn off the vehicle without the gear in the P (Park) position.
If this occurs, the Engine Start/Stop button turns to the ACC position.
Low key battery
When the Engine Start/Stop button is pressed to turn OFF the engine, this message may be displayed. This message indicates that the internal battery of the Smart Key is low. Consider replacing the Smart Key internal battery.
Press START button while turning wheel
This message is displayed if the steering wheel does not unlock normally when the Engine Start/Stop button is pressed.
You should press the Engine Start/Stop button while turning the steering wheel right and left.
Check steering wheel lock system
This message is displayed if the steering wheel does not lock normally while the Engine Start/Stop button is pressed to the OFF position.
Press brake pedal to start engine
This message is displayed if the Engine Start/Stop button changes to the ACC position twice by pressing the button repeatedly without depressing the brake pedal.
You can start the vehicle by depressing the brake pedal and then pressing the Engine Start/Stop button.
Key not in vehicle
This message is displayed if the smart key is not in the vehicle when you leave the vehicle with the Engine Start/Stop button in the ON or Start position.
Always turn off the engine before leaving your vehicle.
Key not detected
This message is displayed if the smart key is not detected when you press the Engine Start/Stop button.
Press START button again
This message is displayed if you were unable to start the vehicle when the Engine Start/Stop button was pressed.
If this occurs, attempt to start the engine by pressing the Engine Start/ Stop button again.
If the warning message appears each time you press the Engine Start/Stop button, we recommend that you have the vehicle inspected by an authorized HYUNDAI dealer.
Press START button with key
This message is displayed if you press the Engine Start/Stop button while the warning message "Key not detected" is displayed.
At this time, the immobilizer indicator light blinks.
Check BRAKE SWITCH fuse
This message is displayed if the brake switch fuse is disconnected.
You need to replace the fuse with a new one before starting the engine.
If that is not possible, you can start the engine by pressing the Engine Start/ Stop button for 10 seconds in the ACC position.
Shift to P or N to start engine
This message is displayed if you try to start the engine in any other position except P (Park) or N (Neutral).
Information
You can start the engine with the gear in N (Neutral). But, for your safety, we recommend that you start the engine with the gear shifted to P (Park).
Battery discharging due to external electrical devices
This message is displayed if the vehicle battery voltage is low or if a current draw is detected that could drain the vehicle battery.
Check to see that there are no nonfactory external electronic devices connected to the vehicle battery system, otherwise battery discharge may occur.
If this message appears in the LCD cluster and there are no other nonfactory electronic devices connected to the vehicle, have the vehicle inspected by an authorized HYUNDAI dealer.
Door, Hood, Liftgate open indicator
This warning is displayed if any door or hood or liftgate is left open. The warning will indicate which door is open in the display.
CAUTION
Before driving the vehicle, you should confirm that the door/ hood/liftgate is fully closed.
Also, check there is no door/hood/ liftgate open warning light or message displayed on the instrument cluster.
Sunroof open indicator (if equipped)
This warning is displayed if you turn off the engine when the sunroof is open.
Close the sunroof securely before leaving your vehicle.
Low tire pressure
This warning message is displayed if the tire pressure is low. The corresponding tire on the vehicle will be illuminated.
For more details, refer to "Tire Pressure Monitoring System (TPMS)" section in chapter 8.
Lights
This indicator displays which exterior light is selected using the lighting control.
You can activate or deactivate Wiper/ Lights display function from the User Settings menu in the cluster LCD display.
Select:
- Setup → User settings → Cluster → Wiper/Lights display
Wiper
This indicator displays which wiper speed is selected using the wiper control.
You can activate or deactivate Wiper/ Lights display function from the User Settings menu in the cluster LCD display.
Select:
- Setup → User settings → Cluster → Wiper/Lights display
Low washer fluid (if equipped)
This message is displayed if the washer fluid level in the reservoir is nearly empty.
Have the washer fluid reservoir refilled.
Low fuel
This message is displayed if the fuel tank is almost out of fuel.
When this message is displayed, the low fuel level warning light in the cluster will come on.
It is recommended to look for the nearest fueling station and refuel as soon as possible.
Low engine oil
This warning message is displayed when the engine oil level should be checked.
If this warning message is displayed, check the engine oil level as soon as possible and add engine oil as required.
Slowly pour the recommended oil little by little into a funnel.
Use only the specified engine oil. (Refer to "Recommended Lubricants and Capacities" section in chapter 2.) Do not overfill the engine oil. Make sure the oil level is not above F (Full) mark on the dipstick.
Engine overheated / Engine has overheated
This message is displayed when the engine coolant temperature is above 248ºF (120ºC). This means that the engine is overheated and may be damaged.
If your vehicle is overheated, refer to "Overheating" section in chapter 8.
Check headlight
This warning message is displayed if the headlamps are not operating properly.
In addition, if a specific lamp(turn signal lamp etc.) is not operating properly, the warning message according to a specific lamp (turn signal lamp etc.) is displayed.
A corresponding bulb may need to be replaced.
Make sure to replace the burned out bulb with a new one of the same wattage rating.
Check turn signal
This message is displayed if the turn signal lamps are not operating properly.
A lamp may need to be replaced.
Make sure to replace the burned out bulb with a new one of the same wattage rating.
Check headlamp LED
This message is displayed if there is a problem with the LED headlamp. We recommend that you have the vehicle inspected by an authorized HYUNDAI dealer.
Check Forward Collision-Avoidance Assist system
This warning message is displayed if there is a problem with Forward Collision-Avoidance Assist. Have the vehicle inspected by an authorized HYUNDAI dealer.
For more details, refer to "Forward Collision-Avoidance Assist (FCA)" in chapter 6.
Check Lane Keeping Assist system
This warning message is displayed if there is a problem with Lane Keeping Assist. Have the vehicle inspected by an authorized HYUNDAI dealer.
For more details, refer to "Lane Keeping Assist (LKA)" in chapter 6.
Check Blind-Spot Collision Warning system (if equipped)
This warning message is displayed if there is a problem with Blind-Spot Collision Warning. Have the vehicle inspected by an authorized HYUNDAI dealer.
For more details, refer to "Blind-Spot Collision Warning (BCW) " in chapter 6.
Check Driver Attention Warning system
This warning message is displayed if there is a problem with Driver Attention Warning. Have the vehicle inspected by an authorized HYUNDAI dealer.
For more details, refer to "Driver Attention Warning (DAW)" in chapter 6.
Check High Beam Assist system
This warning message is displayed if there is a problem with the High Beam Assist. Have the vehicle inspected by an authorized HYUNDAI dealer.
For more details, refer to "High Beam Assist (HBA)" in chapter 5.
Check Smart Cruise Control system (if equipped)
This warning message is displayed if there is a problem with Smart Cruise Control. Have the vehicle inspected by an authorized HYUNDAI dealer.
For more details, refer to "Smart Cruise Control (SCC)" in chapter 6.
READ NEXT:
LCD display control
The LCD display modes can be changed by using the control buttons.
MODE button for changing modes
MOVE switch for changing items
SELECT/RESET button for setting
or resetting the selected item
Information
When the infotainment system
Trip computer (Type A)
The trip computer is a microcomputercontrolled
driver information system that
displays information related to driving.
Information
Some driving information stored in the
trip computer (for example Average
Vehicle Speed) resets if the battery is
SEE MORE:
Suction & Liquid Pipe Assembly
Components
Suction & Liquid Pipe Assembly
Replacement
If a compressor is available, the air conditioner is operated for a few
minutes in the engine idle state and then
the engine is stopped.
Disconnect the negative (-) batte
Differential Carrier Assembly - Reassembly
Reassembly
Pinion drive gear assembly
Install the inner pinion bearing adjustment shim (A) 011 the pinion
drive gear assembly.
Install the inner pinion bearing (A) on the pinion drive gear using SST
(0K530-P2200) and press.
Information
- Home
- Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Owner's Manual
- Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Workshop Manual